THVD Register Map
This register map contains parameters that are used to Line and Tune Currents in Amps RMS. Note that some parameters shown below may not exist in the parameter database/ or shown in PQVision. These parameters have been reserved for future use and are enabled in EtherNet/IP EDS File.
Note:
All parameters with an asterisk (*) in the description will require the Tech level access codes parameter key A: 0x007D (125) and parameter key B: 0xEA6E (60014). All parameters are enabled for communication to EtherNet/IP unless explicitly stated otherwise in the Notes Column of the Table.
Table
8
: Current Feedback and Setpoint Parameters Register Map
Parameter Name (EtherNet Name) | Instance ID | Description | Type | Default & Ranges | Notes |
V_LINE_AB_THD (VLineABTHD) | 222 | Line voltage phase AB THD | R | Default:0 | 10 = 1.0% |
V_LINE_BC_THD (VLineBCTHD) | 223 | Line voltage phase BC THD | R | Default:0 | 10 = 1.0% |
V_LINE_CA_THD (VLineCATHD) | 224 | Line voltage phase CA THD | R | Default:0 | 10 = 1.0% |
V_LOAD_AB_THD (VLoadABTHD) | 237 | Load voltage phase AB THD | R | Default:0 | 10 = 1.0% |
V_LOAD_BC_THD (VLoadBCTHD) | 238 | Load voltage phase BC THD | R | Default:0 | 10 = 1.0% |
V_LOAD_CA_THD (VLoadCATHD) | 239 | Load voltage phase CA THD | R | Default:0 | 10 = 1.0% |
V_TUNE_A_THD (VTuneABTHD) | 249 | Tuned circuit voltage phase AB THD | R | Default:0 | 10 = 1.0% |
V_TUNE_B_THD (VTuneBCTHD) | 250 | Tuned circuit voltage phase BC THD | R | Default:0 | 10 = 1.0% |
V_TUNE_C_THD (VTuneCATHD) | 251 | Tuned circuit voltage phase CA THD | R | Default:0 | 10 = 1.0% |
FAULT_HIGH_THD_ONSET (VLineHighTHDOnset) | 71 | Voltage THD high onset threshold | R/W | Default:120 Range:20 to 200 | Percent rated voltage |
FAULT_HIGH_THD_CLEAR (VLineHighTHDClear) | 72 | Voltage THD high clear threshold | R/W | Default:110 Range:20 to 200 | Percent rated voltage) |
FAULT_HIGH_THD_DELAY (VLineHighTHDDelay) | 73 | Voltage THD high delay time, | R/W | Default:20 Range:1 to 3600 | seconds |
STATUS_HIGH_THD_WARNING_ ONSET (VLineHighTHDWrnOnset) | 75 | Voltage THD high warning onset threshold, (Percent) | R/W | Default:0 Range:0 to 0 | EtherNet/IP Only: Reserved Does not exist in Database |
STATUS_HIGH_THD_WARNING_ CLEAR (VLineHighTHDWrnClear) | 76 | Voltage THD high warning clear threshold, (Percent) | R/W | Default:0 Range:0 to 0 | |
STATUS_HIGH_THD_WARNING_ DELAY (VLineHighTHDWrnDelay) | 77 | Voltage THD high warning delay time, (sec) | R/W | Default:0 Range:0 to 0 | |
V_THD_SCALAR (VTHDScalar) | 115 | Voltage THD gain adjustment factor | R/W | Default:16384 Range: -32768 to 32767 | Value set by Factory |
Provide Feedback