Onset and Delay Register Map
The Onset and Delay Register map contains parameters used by the PQconnect board for fault and status detection logic. Onset is the level at which the fault/status detection activates changing the threshold can cause fault to occur earlier or later. Clear is the level at which the fault/status detection is deemed no longer present and allowing the filter to return to normal operation. Note that some parameters shown below may not exist in the parameter database/ or shown in PQVision. These parameters have been reserved for future use.
Note:
All parameters with an asterisk (*) in the description will require the Tech level access codes parameter key A: 0x007D (125) and parameter key B: 0xEA6E (60014). All parameters are enabled for communication to EtherNet/IP unless explicitly stated otherwise in the Notes Column of the Table.
Table
14
: Onset and Delay Feedback and Setpoint Parameters Register Map
Parameter Name (EtherNet/IP Name) | Instance ID | Description | Type | Default & Ranges | Notes |
V_LINE_OV_ONSET (VLineOVOnset) | 43 | Overvoltage onset threshold, (percent rated voltage) | R/W | Default:130 Range:100 to 150 | |
V_LINE_OV_CLEAR (VLineOVClear) | 44 | Overvoltage clear threshold, (percent rated voltage) | R/W | Default:125 Range:90 to 140 | |
V_LINE_OV_DELAY (VLineOVDelay) | 45 | Overvoltage delay time, (sec) | R/W | Default:2 Range:1 to 3600 | |
V_LINE_UV_ONSET (VLineUVOnset) | 46 | Undervoltage phase loss onset threshold, (percent rated voltage) | R/W | Default:75 Range:50 to 90 | |
V_LINE_UV_CLEAR (VLineUVClear) | 47 | Undervoltage phase loss clear threshold, (percent rated voltage) | R/W | Default:80 Range:60 to 100 | |
V_LINE_UV_DELAY (VLineUVDelay) | 48 | Undervoltage phase loss delay time, (sec) | R/W | Default:1 Range:1 to 3600 | |
I_LINE_OC_ONSET (ILineOCOnset) | 49 | Overcurrent onset threshold, (percent rated current) | R/W | Default:150 Range:100 to 200 | |
I_LINE_OC_CLEAR (ILineOCClear) | 50 | Overcurrent clear threshold, (percent rated current) | R/W | Default:140 Range:90 to 190 | |
I_LINE_OC_DELAY (ILineOCDelay) | 51 | Overcurrent delay time, (sec) | R/W | Default:5 Range:1 to 3600 | |
I_LOAD_BALANCE_ONSET (ILoadBalanceOnset) | 52 | Load current balance onset threshold, (percent rated current ) | R/W | Default:75 Range:10 to 90 | |
I_LOAD_BALANCE_CLEAR (ILoadBalanceClear) | 53 | Load current balance clear threshold, (percent rated current ) | R/W | Default:80 Range:10 to 90 | |
I_LOAD_BALANCE_DELAY (ILoadBalanceDelay) | 54 | Load current balance delay time, (sec) | R/W | Default:4 Range:1 to 3600 | |
I_LOAD_BALANCE_MIN_CURRENT (ILoadBalanceMin) | 55 | Load current balance minimum detect current, (percent rated current) | R/W | Default:50 Range:10 to 100 | |
I_TUNE_OC_ONSET (ITuneOCOnset) | 56 | Tune overcurrent onset threshold, (Percent rated current) | R/W | Default:150 Range:100 to 200 | |
I_TUNE_OC_CLEAR (ITuneOCClear) | 57 | Tune overcurrent clear threshold, (Percent rated current) | R/W | Default:140 Range:90 to 190 | |
I_TUNE_OC_DELAY (ITuneOCDelay) | 58 | Tune overcurrent delay time, (sec) | R/W | Default:4 Range:1 to 3600 | |
I_TUNE_UC_ONSET (ITuneUCOnset) | 59 | Tune circuit fundamental undercurrent onset threshold , (percent rated current ) | R/W | Default:65 Range:10 to 100 | |
I_TUNE_UC_CLEAR (ITuneUCClear) | 60 | Tune circuit fundamental undercurrent clear threshold, (percent rated current ) | R/W | Default:70 Range:15 to 100 | |
I_TUNE_UC_DELAY (ITuneUCDleay) | 61 | Tune circuit fundamental undercurrent delay time, (sec) | R/W | Default:3 Range:1 to 3600 | |
I_TUNE_BALANCE_ONSET (ITuneBalanceOnset) | 62 | Tune circuit current balance onset threshold, (percent rated current ) | R/W | Default:75 Range:10 to 90 | |
I_TUNE_BALANCE_CLEAR (ITuneBalanceClear) | 63 | Tune circuit current balance clear threshold , (percent rated current ) | R/W | Default:80 Range:10 to 90 | |
I_TUNE_BALANCE_DELAY (ITuneBalanceDelay) | 64 | Tune circuit current balance delay time , (sec) | R/W | Default:2 Range:1 to 3600 | |
T_AMBIENT_OT_ONSET (TCtrlOTOnset) | 65 | Controls overtemperature onset threshold , (10 = 1.0 deg C) | R/W | Default:700 Range:100 to 850 | |
T_AMBIENT_OT_CLEAR (TCtrlOTClear) | 66 | Controls overtemperature clear threshold , (10 = 1.0 deg C) | R/W | Default:600 Range:50 to 800 | |
T_AMBIENT_OT_DELAY (TCtrlOTDelay) | 67 | Controls overtemperature delay time , (sec) | R/W | Default:5 Range:1 to 3600 | |
STATUS_T_AMBIENT_UT_ONSET (TCtrlUTOnset) | 68 | Controls under temperature onset threshold, (10 = 1.0 deg C) | R/W | Default:0 Range:0 to 0 | EtherNet Only: Reserved Does not exist in Database |
STATUS_T_AMBIENT_UT_CLEAR (TCtrlUTClear) | 69 | Controls under temperature clear threshold, (10 = 1.0 deg C) | R/W | Default:0 Range:0 to 0 | |
STATUS_T_AMBIENT_UT_DELAY (TCtrlUTDelay) | 70 | Controls under temperature delay time, (10 = 1.0 deg C) | R/W | Default:0 Range:0 to 0 |
Provide Feedback