Communication Register Map
This register map contains parameters which are used to communicate back and forth with the Harmonic Filter. Note that some parameters shown below may not exist in the parameter database/ or shown in PQVision. These parameters have been reserved for future use and are enabled in EtherNet/IP EDS File.
Note:
All parameters with an asterisk (*) in the description will require the Tech level access codes parameter key A: 0x007D (125) and parameter key B: 0xEA6E (60014). All parameters are enabled for communication to EtherNet/IP unless explicitly stated otherwise in the Notes Column of the Table.
Table
4
: Communication Feedback and Setpoint Parameters Register Map
Parameter Name (EtherNet Name) | Instance ID | Description | Type | Default & Ranges | Notes |
BGM_MODULE_STATUS (WLStatus) | 293 | Wireless pairing status | R | Default:0 | Status of the BGM (Bluetooth LE module) 0 = Idle 1 = Advertising 2 = Connected 3 = Not Responding 4 = Radio Disabled 5 = Firmware Mismatch |
SYS_INT_HB (IntHeartbeat) | 298 | System interrupt heartbeat counter | R | Default:0 Range:0 to 65535 | Processor Internal Heartbeat Counter Counts and rolls over to zero used to verify Processor Clock. |
SYS_BG_HB (BGHeartbeat) | 299 | System background heartbeat counter | R | Default:0 Range:0 to 65535 | Processor background heartbeat Counter Counts and rolls over to zero used to verify processor clock operation |
PARAM_KEY_A (ParamKeyA) | 4 | Parameter access key value A | R/W | Default:0 Range:0 to 65535 | Parameter Key Register A User can write the required parameter access key to this parameter and Parameter Key Register B To set the PQconnect board in a different access level. |
PARAM_KEY_B (ParamKeyB) | 5 | Parameter access key value B | R/W | Default:0 Range:0 to 65535 | Parameter Key Register B User can write the required parameter access key to this parameter and Parameter Key Register A To set the PQconnect board in a different access level. |
MB_SLAVE_ADDRESS (ModbusDeviceID) | 35 | Modbus device server address | R/W | Default:10 Range:1 to 247 | Modbus Slave Address |
MB_BAUD_RATE (ModbusBaud) | 36 | Modbus device baud rate, (bits per second) | R/W | Default:11520 Range:0 to 11520 | Modbus Baud Rate 11520 = 115200 baud rate 960 = 9600 baud rate 3840 = 38400 baud rate |
MB_PARITY (ModbusParity) | 37 | Modbus device parity | R/W | Default:2 Range:0 to 2 | 0 = None 1 = Odd 2 = Even |
MB_SAVE_SET_FLAG (ModbusSaveFlag) | 38 | Modbus RTU save new settings | R/W | Default:0 Range:0 to 2 | Modbus Flag Save Settings 0 = Not Saving Settings 1 = Saving Settings" |
BLUETOOTH_ENABLE (BTEn) | 158 | Bluetooth radio enable | R/W | Default:1 Range:0 to 1 | Set to Enable BGM 1 = Enabled 0 = Disabled |
BGM_STATIC_PASSKEY_A (WLPasskeyA) | 174 | Upper 16 bits of wireless password | R/W | Default:1 Range:0 to 15 | |
BGM_STATIC_PASSKEY_B (WLPasskeyB) | 175 | Lower 16 bits of wireless password | R/W | Default:45575 Range:0 to 65535 | |
BGM_SECUIRTY_LEVEL (WLSecurityLevel) | 176 | Wireless security level | R/W | Default:0 Range:0 to 1 | BGM Security level. High Security mode blocks new pairing requests. Passkey changes each time a connection is attempted. 0 = Low Security 1 = High Security |
BGM_NUMERIC_ID (WLNumericID) | 177 | Wireless numeric identifier | R/W | Default:0 Range:0 to 99 | |
BGM_PAIRING_MODE (WLPairingMode) | 178 | Wireless pairing mode request | R/W | Default:0 Range:0 to 1 | 0 = No active request 1 = Active request |
BGM_COMMAND (WLCmd) | 179 | Wireless command input | R/W | Default:0 Range:0 to 255 | |
POWER_CYC_COUNT (PwrCycCount) | 188 | Running number of powers on-off cycles | R/W | Default:0 Range:0 to 0 |
Provide Feedback