Device-defined data types (5094-IB32)

16 points and 16 counters, AB:5000_DI16_Counter16:C:O is the device-defined data type.
20 points and 12 counters, AB:5000_DI20_Counter12:C:O is the device-defined data type.
24 points and 8 counters, AB:5000_DI24_Counter8:C:O is the device-defined data type.
28 points and 4 counters, AB:5000_DI28_Counter4:C:O is the device-defined data type.
32 points and 0 counters, AB:5000_DI32_Counter0:C:O is the device-defined data type.

input (as indicated by an "I")
output (as indicated by an "O")
configuration (as indicated by a "C")
event input (as indicated by an "EI")
event output (as indicated by an "EO")

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Good 1 = Bad
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Pt0x.Data	BOOL	Decimal	0 = Off 1 = On
Pt0x.Fault	BOOL	Decimal	0 = Good 1 = Bad
Pt0x.Uncertain	BOOL	Decimal	0 = Good 1 = Uncertain

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Good 1 = Bad
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Pt0x.Data	BOOL	Decimal	0 = Off 1 = On
Pt0x.Fault	BOOL	Decimal	0 = Good 1 = Bad
Pt0x.Uncertain	BOOL	Decimal	0 = Good 1 = Uncertain
EventStatus[x].EventDropped	BOOL	Decimal	0 = An event status has not been dropped 1 = An event status has been dropped
EventStatus[x].CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
EventStatus[x].CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
EventStatus[x].EventReset	BOOL	Decimal	0 = Do not reset 1 = Reset
EventStatus[x].EventsPending	SINT	Decimal	All positive values
EventStatus[x].EventNumber	DINT	Decimal	All values

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Good 1 = Bad
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Counter0x.Data	BOOL	Decimal	0 = Off 1 = On
Counter0x.Fault	BOOL	Decimal	0 = No fault exists 1 = Fault exists A fault is a roll-up of all of the diagnostic conditions that the device can detect and indicates bad data. If there is a detailed data type member that indicates a given detected condition, this fault member does not affect the DiagnosticActive or DiagnosticSequenceCount members. However, if there is no detailed data type for a given detected condition, this fault member triggers both the DiagnosticActive member and increments/decrements the Diagnostic Sequence Count.
Counter0x.Uncertain	BOOL	Decimal	0 = Valid data 1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.
Counter0x.Done	BOOL	Decimal	0 = On -> Off 1 = I:Count ≥ O:Preset
Counter0x.Rollover	BOOL	Decimal	0 = Counter does not count to the Preset value. 1 = Counter counts to the Rollover value. The counter counted up to Preset -1 and then continued counting from 0. This bit is cleared by the O:RolloverAck bit transitioning from 0 to 1, or by O:Reset transitioning from 0 to 1.
Counter0x.Count	DINT	Decimal	Any
Pt0x.Data	BOOL	Decimal	0 = Output is Off 1 = Output is On
Pt0x.Fault	BOOL	Decimal	0 = Good 1 = Bad
Pt0x.Uncertain	BOOL	Decimal	0 = Good 1 = Uncertain

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Good 1 = Bad
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Counter0x.Data	BOOL	Decimal	0 = Off 1 = On
Counter0x.Fault	BOOL	Decimal	0 = No fault exists 1 = Fault exists A fault is a roll-up of all of the diagnostic conditions that the device can detect and indicates bad data. If there is a detailed data type member that indicates a given detected condition, this fault member does not affect the DiagnosticActive or DiagnosticSequenceCount members. However, if there is no detailed data type for a given detected condition, this fault member triggers both the DiagnosticActive member and increments/decrements the Diagnostic Sequence Count.
Counter0x.Uncertain	BOOL	Decimal	0 = Valid data 1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.
Counter0x.Done	BOOL	Decimal	0 = On -> Off 1 = I:Count ≥ O:Preset
Counter0x.Rollover	BOOL	Decimal	0 = Counter does not count to the Preset value. 1 = Counter counts to the Rollover value. The counter counted up to Preset -1 and then continued counting from 0. This bit is cleared by the O:RolloverAck bit transitioning from 0 to 1, or by O:Reset transitioning from 0 to 1.
Counter0x.Count	DINT	Decimal	Any
Pt0x.Data	BOOL	Decimal	0 = Off 1 = On
Pt0x.Fault	BOOL	Decimal	0 = Good 1 = Bad
Pt0x.Uncertain	BOOL	Decimal	0 = Good 1 = Uncertain
EventStatus[x].EventDropped	BOOL	Decimal	0 = An event status has not been dropped 1 = An event status has been dropped
EventStatus[x].CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
EventStatus[x].CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
EventStatus[x].EventReset	BOOL	Decimal	0 = Do not reset 1 = Reset
EventStatus[x].EventsPending	SINT	Decimal	All positive values
EventStatus[x].EventNumber	DINT	Decimal	All values

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Good 1 = Bad
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Pt0x.Data	BOOL	Decimal	0 = Off 1 = On
Pt0x.Fault	BOOL	Decimal	0 = Good 1 = Bad
Pt0x.Uncertain	BOOL	Decimal	0 = Good 1 = Uncertain
Pt0x.Chatter	BOOL	Decimal	0 = Normal 1 = Input is chattering
Pt0x.TimestampOverflowOffOn	BOOL	Decimal	0 or 1
Pt0x.TimestampOverflowOnOff	BOOL	Decimal	0 or 1
Pt0x.CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
Pt0x.CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
Pt0x.TimestampOffOnNumber	INT	Decimal	All values
Pt0x.TimestampOnOffNumber	INT	Decimal	All values
Pt0x.TimestampOffOn	LINT	Decimal	All values
Pt0x.TimestampOnOff	LINT	Decimal	All values

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Good 1 = Bad
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Pt0x.Data	BOOL	Decimal	0 = Off 1 = On
Pt0x.Fault	BOOL	Decimal	0 = Good 1 = Bad
Pt0x.Uncertain	BOOL	Decimal	0 = Good 1 = Uncertain
Pt0x.Chatter	BOOL	Decimal	0 = Normal 1 = Input is chattering
Pt0x.TimestampOverflowOffOn	BOOL	Decimal	0 or 1
Pt0x.TimestampOverflowOnOff	BOOL	Decimal	0 or 1
Pt0x.CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
Pt0x.CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
Pt0x.TimestampOffOnNumber	INT	Decimal	All values
Pt0x.TimestampOnOffNumber	INT	Decimal	All values
Pt0x.TimestampOffOn	LINT	Decimal	All values
Pt0x.TimestampOnOff	LINT	Decimal	All values
EventStatus[x].EventDropped	BOOL	Decimal	0 = An event status has not been dropped 1 = An event status has been dropped
EventStatus[x].CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
EventStatus[x].CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
EventStatus[x].EventReset	BOOL	Decimal	0 = Do not reset 1 = Reset
EventStatus[x].EventsPending	SINT	Decimal	All positive values
EventStatus[x].EventNumber	DINT	Decimal	All values

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Good 1 = Bad
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
Uncertain	BOOL	Decimal	0 = Valid data 1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Pt0xData	BOOL	Decimal	0 = Off 1 = On
Pt0xFault	BOOL	Decimal	0 = Good 1 = Bad

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Good 1 = Bad
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
Uncertain	BOOL	Decimal	0 = Valid data 1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.
CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Pt0xData	BOOL	Decimal	0 = Off 1 = On
Pt0xFault	BOOL	Decimal	0 = Good 1 = Bad
EventStatus[x].EventDropped	BOOL	Decimal	0 = An event status has not been dropped 1 = An event status has been dropped
EventStatus[x].CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
EventStatus[x].CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
EventStatus[x].EventReset	BOOL	Decimal	0 = Do not reset 1 = Reset
EventStatus[x].EventsPending	SINT	Decimal	All positive values
EventStatus[x].EventNumber	DINT	Decimal	All values

Member Name	Type	Style	Valid Values
Counter0x.Reset	BOOL	Decimal	0 = Does not reset values to zero. 1 = Count and Rollover are set to 0. Resets on transition from 0 to 1.
Counter0x.RolloverAck	BOOL	Decimal	0 = Does not clear Rollover 1 = Clears Rollover
Counter0x.Preset	DINT	Decimal	0...2147483647

Member Name	Type	Style	Valid Values
Pt0x.ResetTimestamps	BOOL	Decimal	0 = Timestamps are not erased 1 = Timestamps are erased
Pt0x.TimestampOffOnNumberAck	INT	Decimal	All values
Pt0x.TimestampOnOffNumberAck	INT	Decimal	All values

Member Name	Type	Style	Valid Values
Pt0x.InputOffOnFilter	SINT	Decimal	9 = 0 µs 10 = 100 µs 11= 200 µs 12 = 500 µs 13 = 1 ms 14 = 2 ms 15 = 5 ms 16 = 10 ms 17 = 20 ms 18 = 50 ms
Pt0x.InputOnOffFilter	SINT	Decimal	9 = 0 µs 10 = 100 µs 11= 200 µs 12 = 500 µs 13 = 1 ms 14 = 2 ms 15 = 5 ms 16 = 10 ms 17 = 20 ms 18 = 50 ms

Member Name	Type	Style	Valid Values
Counter0x.InputOffOnFilter	SINT	Decimal	5 = 0 µs 6 = 5 µs 7 = 10 µs 8 = 20 µs 9 = 50 µs 10 = 100 µs 11= 200 µs 12 = 500 µs 13 = 1 ms 14 = 2 ms 15 = 5 ms 16 = 10 ms 17 = 20 ms 18 = 50 ms
Counter0x.InputOnOffFilter	SINT	Decimal	5 = 0 µs 6 = 5 µs 7 = 10 µs 8 = 20 µs 9 = 50 µs 10 = 100 µs 11= 200 µs 12 = 500 µs 13 = 1 ms 14 = 2 ms 15 = 5 ms 16 = 10 ms 17 = 20 ms 18 = 50 ms
Counter0x.RolloverAtPreset	BOOL	Decimal	0 = Unchecked 1 = Checked
Pt0x.InputOffOnFilter	SINT	Decimal	Pt0x depends on the number of counters that have been configured. 5 = 0 µs 6 = 5 µs 7 = 10 µs 8 = 20 µs 9 = 50 µs 10 = 100 µs 11= 200 µs 12 = 500 µs 13 = 1 ms 14 = 2 ms 15 = 5 ms 16 = 10 ms 17 = 20 ms 18 = 50 ms
Pt0x.InputOnOffFilter	SINT	Decimal	Pt0x depends on the number of counters that have been configured. 5 = 0 µs 6 = 5 µs 7 = 10 µs 8 = 20 µs 9 = 50 µs 10 = 100 µs 11= 200 µs 12 = 500 µs 13 = 1 ms 14 = 2 ms 15 = 5 ms 16 = 10 ms 17 = 20 ms 18 = 50 ms

Member Name	Type	Style	Valid Values
Pt0x.InputOffOnFilter	BOOL	Decimal	0 = Off 1 = On
Pt0x.InputOnOffFilter	BOOL	Decimal	0 = Good 1 = Bad
Pt0x.ChatterTime	INT	Decimal	1...10000
Pt0x.ChatterCount	SINT	Decimal	0 = Disabled 2...127 = Enabled
Pt0x.CaptureOffOnEn	BOOL	Decimal	0 = Capture disabled for OFF to ON input transitions 1 = Capture enabled (default) for OFF to ON input transitions
Pt0x.CaptureOnOffEn	BOOL	Decimal	0 = Capture disabled for ON to OFF input transitions 1 = Capture enabled (default) for ON to OFF input transitions
Pt0x.TimestampLatchEn	BOOL	Decimal	0 = Timestamps are overridden with each successive COS transition 1 = Timestamps are latched until acknowledged

Member Name	Type	Style	Valid Values
RunMode	BOOL	Decimal	0 = Idle 1 = Run
ConnectionFaulted	BOOL	Decimal	0 = Connection working 1 = Not connected
DiagnosticActive	BOOL	Decimal	0 = No diagnostics active 1 = One or more diagnostics are active or the prognostics threshold is reached
DiagnosticSequenceCount	SINT	Decimal	-128...127 The value of 0 is skipped except during device power-up.
Event0x.Fault	BOOL	Decimal	0 = Good 1 = Bad, causing fault If the tag is set to 1, you must troubleshoot the device to correct the case of the incaccuracy. IMPORTANT : Once the condition that causes the tag to change to 1 is removed, the tag automatically resets to 0.
Event0x.Uncertain	BOOL	Decimal	0 = Good data 1 = Uncertain data If the tag is set to 1, you must troubleshoot the device to correct the case of the incaccuracy. IMPORTANT : Once the condition that causes the tag to change to 1 is removed, the tag automatically resets to 0.
Event0x.EventDropped	BOOL	Decimal	0 = An event status has not been dropped. 1 = An event status has been dropped.
Event0x.EventRising	BOOL	Decimal	0 or 1
Event0x.EventFalling	BOOL	Decimal	0 or 1
Event0x.CIPSyncValid	BOOL	Decimal	0 = CIP Sync is not available 1 = CIP Sync is available
Event0x.CIPSyncTimeout	BOOL	Decimal	0 = A valid time master has not timed out 1 = A valid time master was detected on the backplane, but the time master has timed out. The device is using its local clock and can be drifting away from the last known time master.
Event0x.EventsPending	SINT	Decimal	All positive values
Event0x.EventNumber	DINT	Decimal	All values
Event0x.EventTimestamp	LINT	Decimal	All positive values
Event0x.Counter0xDone	BOOL	Decimal	0 = Corresponding counter Done bit did not trigger the event 1 = Corresponding counter Done bit triggered the event
Event0x.Pt0xData	BOOL	Decimal	0 = Corresponding data value did not trigger the event 1 = Corresponding data value triggered the event
Event0x.Counter0xFault	BOOL	Decimal	0 = Corresponding counter did not have a fault indicated when the event occurred 1 = Corresponding counter did have a fault indicated when the event occurred
Event0x.Pt0xFault	BOOL	Decimal	0 = Good 1 = Bad

Member Name	Description	Type	Style	Valid Values
Event0x.En	Determines whether the corresponding event trigger activates. Events are triggered once conditions match the definition.	BOOL	Decimal	0 = Event trigger definition is not active 1 = Event trigger definition is active
Event0x.EventRisingEn	Triggers an event each time a condition change results in conditions matching the event trigger definition.	BOOL	Decimal	When Enable Independent Point Triggers = Checked (EventRisingEn, EventFallingEn) Disable (0,0) On transition (1, 0) On inverted transition (0, 1) On any transition (1, 1) When Enable Independent Point Triggers = Unchecked (EventRisingEn, EventFallingEn) Disable (0, 0) On input transition to match pattern (1, 0) On input transition to not match pattern (0, 1) On input transition to match or not match pattern (1, 1)
Event0x.EventFallingEn	Triggers an event each time a condition change results in conditions no longer matching the event trigger definition.	BOOL	Decimal	When Enable Independent Point Triggers = Checked (EventRisingEn, EventFallingEn) Disable (0, 0) On transition (1, 0) On inverted transition (0, 1) On any transition (1, 1) When Enable Independent Point Triggers = Unchecked (EventRisingEn, EventFallingEn) Disable (0, 0) On input transition to match pattern (1, 0) On input transition to not match pattern (0, 1) On input transition to match or not match pattern (1, 1)
Event0x.LatchEn	Latches an event until it is acknowledged. A new event is lost if the previous event has not been acknowledged. When not set, new events overwrite old events.	BOOL	Decimal	0 = Event is not latched. In this case, new events overwrite old events. 1 = Event is latched. In this case, new events are lost if the latched event has not been acknowledged.
Event0x.ResetEvent	Indicates whether, on a transition from 0 to 1, all events are reset and the event queue on the channel clears.	BOOL	Decimal	0 to 1 transition resets all events and the event queue
Event0x.IndependentConditionTriggerEn	Determines whether each condition indicated in the Event trigger definition can initiate an event independently.	BOOL	Decimal	0 = When all selected conditions achieve the configured values an event is triggered. 1 = When any selected condition achieves the configured value an event is triggered.
Event0x.EventNumberAck	When an event is triggered, the user program in the controller writes back the value of EventNumber to this member to indicate receipt of the event. All events with EventNumbers that occurred before EventNumberAck acknowledged.	DINT	Decimal	Any
Event0x.Counter0xSelect	When using counters, counter with which the event is associated, if any.	BOOL	Decimal	0 = Does not participate in event trigger 1 = Does participate in event trigger
Event0x.Pt0xDataSelect	When set indicates the corresponding data value is to participate in the event trigger definition.	BOOL	Decimal	0 = Does not participate in event trigger 1 = Does participate in event trigger
Event0x.Counter0xValue	Done state for that counter that is used in the trigger.	BOOL	Decimal	0 = Off 1 = On
Event0x.Pt0xDataValue	Input state for the point that is used in the trigger.	BOOL	Decimal	0 = Off 1 = On