Device-defined data types (5069-OF8)

0 = Idle

1 = Run

0 = A connection exists between the device and the controller.

1 = Not connected

0 = No diagnostics active

1 = One or more diagnostics are active or the prognostics threshold is reached

0 to 255

Increments each time a distinct diagnostic condition is detected, and each time a distinct diagnostic condition transitions from detected to not detected.

0 = No fault exists

1 = Fault exists

A fault is a roll-up of all of the diagnostic conditions that the device can detect and indicates bad data. If there is a detailed data type member that indicates a given detected condition, this fault member does not affect the DiagnosticActive or DiagnosticSequenceCount members. However, if there is no detailed data type for a given detected condition, this fault member triggers both the DiagnosticActive member and increments/decrements the Diagnostic Sequence Count.

0 = Valid data

1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.

0 = No load condition does not exist

1 = No load condition exists, meaning a signal wire is disconnected from the channel or the RTB is removed from the device.

0 = No short circuit or overcurrent condition exists

1 = Short circuit or overcurrent exists

0 = Device temperature is not over the operating limits

1 = Device temperature is over the operating limits

0 = Field power is present

1 = Field power is not present

0 = Channel is not holding

1 = Channel is holding

0 = Last channel data received was a number

1 = Output value received from the originator is NotANumber (the IEEE NAN value). The output channel will hold its last state

0 = The input signal at the channel is greater than the minimum detectable signal.

1 = The input signal at the channel is less than or equal to the minimum detectable signal.

0 = The input signal at the channel is less than the maximum detectable signal.

1 = The input signal at the channel is greater than or equal to the maximum detectable signal.

0 = Alarm is not triggered

1 = Alarm is triggered

0 = Alarm is not triggered

1 = Alarm is triggered

0 = Alarm is not triggered

1 = Alarm is triggered

0 = Calibration did not fail

1 = A calibration session for a channel was interrupted or failed. CalFault is reset by product reset or power cycle.

0 = Channel is not being calibrated

1 = Channel is being calibrated

-1.0E11 to 1.0E11

Any positive value.

RollingTimestamp is a continuously running timer that counts in milliseconds. When an input device scans its channels, it also records the RollingTimestamp value.

0 = Alarm is disabled

1 = Alarm is enabled

0 = Alarm is disabled

1 = Alarm is enabled

0 = Alarm is disabled

1 = Alarm is enabled

0 = Alarm is disabled

1 = Alarm is enabled

0 = Alarm is disabled

1 = Alarm is enabled

Transition from low to high unlatches alarm.

Transition from high to low unlatches alarm.

Transition from low to high unlatches alarm

-1.0E11 to 1.0E11

0 = -10…10V

1 = 0…5V

2 = 0…10V

4 = 0…20 mA

5 = 4…20 mA

0 = Alarms are enabled

1 = Alarms are disabled (default)

0 = Latching disabled (default)

1 = Latching enabled

0 = Latching disabled (default)

1 = Latching enabled

0 = Disabled (default)

1 = Enabled

0 = Channel is enabled (default)

1 = Channel is disabled

0 = Transition to user-defined value

1 = Hold Last State (default)

0 = Transition to user-defined value

1 = Hold Last State (default)

0 = Channel remains in Program mode

1 = Channel transitions to Fault mode

0 = Ramping disabled (default)

1 = Ramping enabled in Run mode

0 = Ramping disabled (default)

1 = Ramping enabled to Program mode state

0 = Ramping disabled (default)

1 = Ramping enabled to Fault mode state

0 = Unchecked

1 = Checked

0 = Forever

1 = 1 second

2 = 2 seconds

5 = 5 seconds

10 seconds

-1.0E11 to 1.0E11

-1.0E11 to 1.0E11

A combination of LowSignal, HighSignal, LowEngineering, and HighEngineering are used to scale the input data returned by the device.

-1.0E11 to 1.0E11

A combination of LowSignal, HighSignal, LowEngineering, and HighEngineering are used to scale the input data returned by the device.

-1.0E11 to 1.0E11

A combination of LowSignal, HighSignal, LowEngineering, and HighEngineering are used to scale the input data returned by the device.

-1.0E11 to 1.0E11

A combination of LowSignal, HighSignal, LowEngineering, and HighEngineering are used to scale the input data returned by the device.

-1.0E11 to 1.0E11

-1.0E11 to 1.0E11

-1.0E11 to 1.0E11

-1.0E11 to 1.0E11

-1.0E11 to 1.0E11

-1.0E11 to 1.0E11

0 = Idle

1 = Run

0 = Good

1 = Bad

0 = No diagnostics active

1 = One or more diagnostics are active or the prognostics threshold is reached

0 to 255

0 = Good

1 = Bad

0 = Good

1 = Uncertain

0 = No Load condition does not exist

1 = No load condition exists, meaning a signal wire is disconnected from the channel or the RTB is removed from the device.

0 = No short circuit or overcurrent condition exists

1 = Short circuit or overcurrent exists

0 = Device temperature is not over the operating limits

1 = Device temperature is over the operating limits

0 = Field power is present

1 = Field power is not present

0 = Channel is not holding

1 = Channel is holding

0 = Last channel data received was a number

1 = Last channel data received was not a number

0 = Channel data is not beneath the underrange threshold

1 = Channel data is beneath

0 = Channel data is not above the overrange threshold

1 = Channel data is above the overrange threshold

0 = Alarm is not triggered

1 = Alarm is triggered

0 = Alarm is not triggered

1 = Alarm is triggered

0 = Alarm is not triggered

1 = Alarm is triggered

0 = Calibration did not fail

1 = Calibration failed

0 = Channel is not being calibrated

1 = Channel is being calibrated

0 = Valid Low Reference signal has not been sampled on this channel

1 = Valid Low Reference signal has been sampled on this channel

0 = Invalid Low Reference signal has not been sampled on this channel

1 = Invalid Low Reference signal has been sampled on this channel

0 = Valid High Reference signal has not been sampled on this channel

1 = Valid High Reference signal has been sampled on this channel

0 = Invalid High Reference signal has not been sampled on this channel

1 = Invalid High Reference signal has been sampled on this channel

0 = Calibration was not successful

1 = Calibration was successful and calibrating state has been exited.

-1.0E11 to 1.0E11

Any value

RollingTimestamp is a continuously running timer that counts in milliseconds. When an input device scans its channels, it also records the RollingTimestamp value.

Transition from low to high unlatches alarm.

Transition from high to low unlatches alarm.

Transition from low to high unlatches alarm.

0 = Calibration process is not started (default)

1 = Calibration process is started

0 = Do not output Cal Low Reference

1 = Output Calibration Low Reference

0 = Do not Output Cal High Reference

1 = Output Calibration High Reference Signal

0 = Not sending Recorded Cal Low Ref

1 = Sending Recorded Cal Low Reference in Output Data for Calibration Verification

0 = Not sending Cal High Reference

1 = Sending recorded Calibration High Reference Signal in Output Data for Calibration Verification

0 = Channel not triggered to complete the calibration procedure

1 = Channel triggered to complete the calibration procedure

-1.0E11 to 1.0E11