Device-defined data types (5069-IY4)

Device-defined data type names vary for each device depending on selections made when the device was created.
These tables list and describe device-defined data types for the 5069-IY4 devices.
These tables include information for:
  • input (as indicated by an "I")
  • output (as indicated by an "O")
  • configuration (as indicated by a "C")
Device-defined data type: AB:5000_AI4CJ:I:0
Connection Type: Data and Listen Only
Member Name
Type
Style
Valid Values
RunMode
BOOL
Decimal
0 = Idle
1 = Run
  • Output products follow the Run mode of the owning connection.
  • Input-only products are always in Run mode.
ConnectionFaulted
BOOL
Decimal
0 = A connection exists between the device and the controller.
1 = Bad
DiagnosticActive
BOOL
Decimal
0 = No diagnostics active
1 = One or more diagnostics are active or the prognostics threshold is reached.
DiagnosticSequenceCount
BOOL
Decimal
0 to 255
Increments each time a distinct diagnostic condition is detected, and each time a distinct diagnostic condition transitions from detected to not detected.
CJCh0x.Fault
BOOL
Decimal
0 = No fault exists
1 = Fault exists
A fault is a roll-up of all of the diagnostic conditions that the device can detect and indicates bad data. If there is a detailed data type member that indicates a given detected condition, this fault member does not affect the DiagnosticActive or DiagnosticSequenceCount members. However, if there is no detailed data type for a given detected condition, this fault member triggers both the DiagnosticActive member and increments/decrements the Diagnostic Sequence Count.
CJCh0x.Uncertain
BOOL
Decimal
0 = Valid data
1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.
CJCh0x.NoLoad
BOOL
Decimal
0 = No load condition does not exist
1 = No load condition exists, meaning a signal wire is disconnected from the channel or the RTB is removed from the device.
CJCh0x.OpenWire
BOOL
Decimal
0 = Open wire condition does not exist or open wire detection is disabled.
1 = Open wire condition exists, meaning the signal wire is disconnected from the channel or the RTB is removed from the device.
CJCh0x.FieldPowerOff
BOOL
Decimal
0 = Field power is present
1 = Field power is not present
CJCh0x.Underrange
BOOL
Decimal
0 = The input signal at the channel is greater than the minimum detectable signal.
1 = The input signal at the channel is less than or equal to the minimum detectable signal.
CJCh0x.Overrange
BOOL
Decimal
0 = The input signal at the channel is less than the maximum detectable signal.
1 = The input signal at the channel is greater than or equal to the maximum detectable signal.
CJCh0x.Temperature
BOOL
Decimal
The current temperature of the cold junction.
Ch0x.Fault
BOOL
Decimal
0 = No fault exists
1 = Fault exists
A fault is a roll-up of all of the diagnostic conditions that the device can detect and indicates bad data. If there is a detailed data type member that indicates a given detected condition, this fault member does not affect the DiagnosticActive or DiagnosticSequenceCount members. However, if there is no detailed data type for a given detected condition, this fault member triggers both the DiagnosticActive member and increments/decrements the Diagnostic Sequence Count.
Ch0x.Uncertain
BOOL
Decimal
0 = Valid data
1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.
Ch0x.OpenWire
BOOL
Decimal
0 = Open wire condition does not exist
1 = Open wire condition exists. A signal wire is disconnected from the channel or the RTB
Ch0x.OverTemperature
BOOL
Decimal
0 = Device temperature is not over the operating limits
1 = Device temperature is over the operating limits
Ch0x.FieldPowerOff
BOOL
Decimal
0 = Field power is present
1 = Field power is not present
Ch0x.NotANumber
BOOL
Decimal
0 = Last channel data received was a number
1 = Last channel data received was not a number
Ch0x.Underrange
BOOL
Decimal
0 = The input signal at the channel is greater than the minimum detectable signal.
1 = The input signal at the channel is less than or equal to the minimum detectable signal.
Ch0x.Overrange
BOOL
Decimal
0 = The input signal at the channel is less than the maximum detectable signal.
1 = The input signal at the channel is greater than or equal to the maximum detectable signal.
Ch0x.LLAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = The input signal has moved below the configured Low Low Alarm Limit. It remains set until the signal moves above the configured Low Low Alarm Limit plus Deadband if specified.
Ch0x.LAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = The input signal has moved below the configured Low Alarm Limit. It remains set until the signal moves above the configured Low Low Alarm Limit plus Deadband if specified.
Ch0x.HAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = The input signal has moved above the configured High Alarm Limit. It remains set until the signal moves below the configured High High Alarm Limit minus Deadband if specified.
Ch0x.HHAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = The input signal has moved above the configured High HIgh Alarm Limit. It remains set until the signal moves below the configured High High Alarm Limit minus Deadband if specified.
Ch0x.RateAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = The input channel’s rate of change exceeds the configured rate alarm. It remains set until the rate of change drops below the configured rate.
Ch0x.CalFault
BOOL
Decimal
0 = Calibration did not fail
1 = A calibration session for a channel was interrupted or failed. CalFault is reset by product reset or power cycle.
Ch0x.Calibrating
BOOL
Decimal
0 = Channel is not being calibrated
1 = Channel is being calibrated
Ch0x.Data
REAL
Float
-1.0E11 to 1.0E11
Ch0x.RollingTimeStamp
INT
Decimal
Any positive value.
RollingTimestamp is a continuously running timer that counts in milliseconds. When an input device scans its channels, it also records the RollingTimestamp value.
Device-defined data type: AB:5000_AI4:O:0
Connection Type: Data with Calibration
Member Name
Type
Style
Valid Values
Ch0x.LLAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled
Ch0x.LAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled
Ch0x.HAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled
Ch0x.HHAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled
Ch0x.RateAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled
Ch0x.LLAlarmUnlatch
BOOL
Decimal
Transition from low to high unlatches alarm.
Ch0x.LAlarmUnlatch
BOOL
Decimal
Transition from low to high unlatches alarm.
Ch0x.HAlarmUnlatch
BOOL
Decimal
Transition from high to low unlatches alarm.
Ch0x.HHAlarmUnlatch
BOOL
Decimal
Transition from high to low unlatches alarm.
Ch0x.RateAlarmUnlatch
BOOL
Decimal
Transition from low to high unlatches alarm.
Ch0x.SensorOffset
REAL
Float
-1.0E11 to 1.0E11
A user-defined offset in engineering units added directly into the scaled data, used to compensate for inherent sensor offset. Commonly used with thermocouple sensors to offset accuracy issues.
Device-defined data type: AB:5000_AI4CJ:C:0
Connection Type: Data and Data with Calibration
Member Name
Type
Style
Valid Values
CJCh0x.Disable
BOOL
Decimal
0 = Cold junction compensation is enabled
1 = Cold junction compensation is disabled
CJCh0x.Remote
BOOL
Decimal
0 = Cold junction sensor is not mounted on a remote termination block
1 = Cold junction sensor is mounted on a remote termination block
CJCh0x.SensorOffset
REAL
Float
-1.0E11 to 1.0E11
Any value within the channel’s operating range.
Ch0x.Range
SINT
Decimal
0 = -10…10V
1 = 0…5V
2 = 0…10V
4 = 0…20 mA
5 = 4…20 mA
6 = -100...100 mV
8 = 1…487 Ohm 2-wire
9 = 2…1,000 Ohm 2-wire
10 = 4…2,000 Ohm 2-wire
11 = 8…4,000 Ohm 2-wire
12 = 1...487 Ohm 3-wire
13 = 2…1,000 Ohm 3-wire
14 = 4…2,000 Ohm 3-wire
15 = 8…4,000 Ohm 3-wire
Ch0x.SensorType
BOOL
Decimal
If the input type is RTD:
0 =no linearization, Ohm
1 = 100 Ohm Platinum 385
2 = 200 Ohm Platinum 385
3 = 500 Ohm Platinum 385
4 = 1000 Ohm Platinum 385
5 = 100 Ohm Platinum 3916
6 = 200 Ohm Platinum 3916
7 = 500 Ohm Platinum 3916
8 = 1000 Ohm Platinum 3916
9 = 10 Ohm Copper 427
10 = 120 Ohm Nickel 672
11 = 100 Ohm Nickel 618
12 = 120 Ohm Nickel 618
13 = 200 Ohm Nickel 618
14 = 500 Ohm Nickel 618
If input type is Thermocouple:
0 = mV
1 = B
2 = C
3 = E
4 = J
5 = K
6 = N
7 = R
8 = S
9 = T
10 = TXK/XK (L)
11 = D
Ch0x.NotchFilter
SINT
Decimal
0 = 10 Hz (simultaneous 50/60Hz rejection)
1 = 50 Hz
2 = 60 Hz
3 = 100 Hz
4 = 200 Hz
5 = 500 Hz
6 = 1,000 Hz
7 = 2,500 Hz
8 = 5,000 Hz
9 = 10,000 Hz
10 = 15,625 Hz
11 = 25,000 Hz
12 = 31,250 Hz
13 = 5 Hz
14 = 62,500 Hz
15 = 15 Hz
16 = 20 Hz
Ch0x.AlarmDisable
BOOL
Decimal
0 = Alarms are enabled
1 = Alarms are disabled (default) for the channel
Ch0x.ProcessAlarmLatchEn
BOOL
Decimal
0 = Latching disabled (default)
1 = Latching enabled
Ch0x.RateAlarmLatchEn
BOOL
Decimal
0 = Latching disabled (default)
1 = Latching enabled
Ch0x.OpenWireEn
BOOL
Decimal
0 = Disabled (default)
1 = Enabled
Ch0x.Disable
BOOL
Decimal
0 = Channel is enabled (default)
1 = Channel is disabled
Ch0x.TenOhmOffset
BOOL
Decimal
-100 to 100
Ch0x.DigitalFilter
BOOL
Decimal
Any positive value
Ch0x.LowSignal
REAL
Float
-1.0E11 to 1.0E11
A combination of LowSignal, HighSignal, LowEngineering, and HighEngineering are used to scale the input data returned by the device.
Ch0x.HighSignal
REAL
Float
-1.0E11 to 1.0E11
A combination of LowSignal, HighSignal, LowEngineering, and HighEngineering are used to scale the input data returned by the device.
Ch0x.LowEngineering
REAL
Float
-1.0E11 to 1.0E11
A combination of LowSignal, HighSignal, LowEngineering, and HighEngineering are used to scale the input data returned by the device.
Ch0x.HighEngineering
REAL
Float
-1.0E11 to 1.0E11
A combination of LowSignal, HighSignal, LowEngineering, and HighEngineering are used to scale the input data returned by the device.
Ch0x.LLAlarmLimit
REAL
Float
-1.0e+11 to 1.0e++11
The low low alarm trigger point.
Ch0x.LAlarmLimit
REAL
Float
-1.0e+11 to 1.0e++11
The low alarm trigger point.
Ch0x.HAlarmLimit
REAL
Float
-1.0e+11 to 1.0e++11
The high alarm trigger point.
Ch0x.HHAlarmLimit
REAL
Float
-1.0e+11 to 1.0e++11
The high high alarm trigger point.
Ch0x.RateAlarmLimit
REAL
Float
0.0 to 1.0e++11
Ch0x.AlarmDeadband
REAL
Float
0.0 to 1.0e++11
Device-defined data type: AB:5000_AI4CJ_CAL:I:0
Connection type: Data with Calibration
Member Name
Type
Style
Valid Values
RunMode
BOOL
Decimal
0 = Idle
1 = Run
ConnectionFaulted
BOOL
Decimal
0 = Connection working
1 = Not connected
DiagnosticActive
BOOL
Decimal
0 = No diagnostics active
1 = One or more diagnostics are active or the prognostics threshold is reached
DiagnosticSequenceCount
SINT
Decimal
0 to 255
Count that increments for each diagnostic.
CJCh0x.Fault
BOOL
Decimal
0 = Good
1 = Bad
CJCh0x.Uncertain
BOOL
Decimal
0 = Valid data
1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.
CJCh0x.OpenWire
BOOL
Decimal
0 = Open wire condition does not exist or open wire detection is disabled.
1 = Open wire condition exists, meaning the signal wire is disconnected from the channel or the RTB is removed from the device.
CJCh0x.FieldPowerOff
BOOL
Decimal
0 = Field power is present
1 = Field power is not present
CJCh0x.Underrange
BOOL
Decimal
0 = Channel data is not beneath the underrange threshold
1 = Input signal at the channel is less than or equal to the minimum detectable signal
CJCh0x.Overrange
BOOL
Decimal
0 = Channel data is not above the overrange threshold
1 = Input signal at the channel is greater than or equal to the maximum detectable signal.
CJCh0x.Temperature
REAL
Float
-1.0E11 to 1.0E11
Ch0x.Fault
BOOL
Decimal
0 = Good
1 = Bad
Ch0x.Uncertain
BOOL
Decimal
0 = Valid data
1 = Data validity uncertain. Device is operating outside its designed operating range, or data is under manual or override control.
Ch0x.OpenWire
BOOL
Decimal
0 = Open wire condition does not exist or open wire detection is disabled.
1 = Open wire condition exists, meaning the signal wire is disconnected from the channel or the RTB is removed from the device.
Ch0x.OverTemperature
BOOL
Decimal
0 = Device temperature is not over the operating limits
1 = Device temperature is over the operating limits
Ch0x.FieldPowerOff
BOOL
Decimal
0 = Field power is present
1 = Field power is not present
Ch0x.NotANumber
BOOL
Decimal
0 = Last channel data received was a number
1 = Last channel data received was not a number
Ch0x.Underrange
BOOL
Decimal
0 = Channel data is not beneath the underrange threshold
1 = Input signal at the channel is less than or equal to the minimum detectable signal
Ch0x.Overrange
BOOL
Decimal
0 = Channel data is not above the overrange threshold
1 = Input signal at the channel is greater than or equal to the maximum detectable signal.
Ch0x.LLAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = Alarm is triggered
Ch0x.LAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = Alarm is triggered
Ch0x.HAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = Alarm is triggered
Ch0x.HHAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = Alarm is triggered
Ch0x.RateAlarm
BOOL
Decimal
0 = Alarm is not triggered
1 = Alarm is triggered
Ch0x.CalFault
BOOL
Decimal
0 = Calibration did not fail
1 = Calibration error occurred during calibration of the channel
Ch0x.Calibrating
BOOL
Decimal
0 = Channel is not being calibrated
1 = Channel is being calibrated
Ch0x.CalFault
BOOL
Decimal
0 = Calibration did not fail
1 = Calibration error occurred during calibration of the channel
Ch0x.Calibrating
BOOL
Decimal
0 = Channel is not being calibrated
1 = Channel is being calibrated
Ch0x.CalGoodLowRef
BOOL
Decimal
0 = Valid Low Reference signal has not been sampled on this channel
1 = Valid Low Reference signal has been sampled on this channel
Ch0x.CalBadLowRef
BOOL
Decimal
0= Invalid Low Reference signal has not been sampled on this channel
1 = Invalid Low Reference signal has been sampled on this channel
Ch0x.CalGoodHighRef
BOOL
Decimal
0 = Valid High Reference signal has not been sampled on this channel
1 = Valid High Reference signal has been sampled on this channel
Ch0x.CalBadHighRef
BOOL
Decimal
0 = Invalid High Reference signal has not been sampled on this channel
1 = Invalid High Reference signal has been sampled on this channel
Ch0x.CalSuccessful
BOOL
Decimal
0 = Calibration was not successful
1 = Calibration was successful and calibrating state has been exited.
Ch0x.Data
REAL
Float
-1.0E11 to 1.0E11
Ch0x.RollingTimestamp
INT
Decimal
Any positive value
A continuously running 15-bit timer that counts in milliseconds (unrelated to the Coordinated System Time).
Device-defined data type: AB:5000_AI4_CAL:O:0
Connection type: Data with Calibration
Member Name
Type
Style
Valid Values
Ch0x.LLAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled for the channel low low alarm
Ch0x.LAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled for the channel low alarm
Ch0x.HLAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled for the channel high alarm
Ch0x.HHAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled for the channel high high alarm
Ch0x.RateAlarmEn
BOOL
Decimal
0 = Alarm is disabled
1 = Alarm is enabled for the channel rate alarm
Ch0x.LLimitAlarmUnlatch
BOOL
Decimal
Transition from low to high unlatches alarm.
Ch0x.HLimitAlarmUnlatch
BOOL
Decimal
Transition from high to low unlatches alarm.
Ch0x.RampAlarmUnlatch
BOOL
Decimal
Transition from low to high unlatches alarm
Ch0x.Calibrate
BOOL
Decimal
0 = Channel is not being calibrated
1 = Channel is being calibrated
Ch0x.CalLowRef
BOOL
Decimal
0 = Channel data value has not passed the Low Reference Point value the current InputRange value
1 = Channel data value has passed the Low Reference Point value the current InputRange value
Ch0x.CalHighRef
BOOL
Decimal
0 = Channel data value has not passed the high reference point for the current InputRange value
1 = Channel data value has passed the high reference point for the current InputRange value
Ch0x.SensorOffset
REAL
Float
-1.0E11 to 1.0E11
Provide Feedback
Have questions or feedback about this documentation? Please submit your feedback here.
Normal